On router R1, in the global configuration mode, enter the router riprouter ripThe Routing Information Protocol (RIP) is one of the oldest distance-vector routing protocols which employs the hop count as a routing metric. RIP prevents routing loops by implementing a limit on the number of hops allowed in a path from source to destination.

What is the command to enable RIPv2?

Using the Cisco IOS, the command to enable RIP routing protocol is router rip. The version command is used to specify which RIP version to use (either 1 or 2). If the version command is omitted then the router defaults to sending RIPv1 but can receive both RIPv1 and RIPv2.

How do I enable IP RIP?

Configuring RIP requires the following steps:

  1. Step 1 Enable the RIP routing process, which places you in router configuration mode via the Router#router rip command.
  2. Step 2 Specify those networks that should be advertised using RIP via the Router(config-router)#network [network-number] command.

What are the steps required to configure RIPv2 authentication?

RIPv2 Authentication – Configuration Steps

  1. Define a key chain with a name. …
  2. Define the key or keys on the key chain and specify the password or key-string to be used in the key. …
  3. Enable authentication on an interface and specify the key chain to be used.

Should I enable RIP on my router?

RIP is a dynamic routing protocol. Unless you have multiple routers you need to distribute routes to there really isn’t any reason to run it. All it will do is put extra traffic on the wire and eat up a few cpu cycles on your router.

How do I see rips on my router?

Displaying RIP Routes

To see a listing of the RIP routes in the switch’s routing table, use the show ip rip database command. (You can also display similar information using the RIP option in the show ip route command.) This command displays all active rip routes.

What is a purpose of the network command when configuring RIPv2 as the routing protocol?

What is a purpose of the network command when configuring RIPv2 as the routing protocol? It identifies the interfaces that belong to a specified network. A network administrator configures a static route on the edge router of a network to assign a gateway of last resort.

What two commands are needed to configure RIP on a router?

Only three steps are required:

  • enabling RIP by using the router rip global configuration command.
  • instructing the router to use RIPv2 by typing the version 2 command.
  • telling RIP which networks to advertise by using one or more network commands.

How do RIPv1 and RIPv2 differ *?

RIP v1 is an older, no longer much used routing protocol. RIP v2 is a classless protocol and it supports classful, variable-length subnet masking (VLSM), CIDR, and route summarization. RIPv2 supports authentication of RIPv2 update messages (MD5 or plain-text).

What is RIP in Cisco router?

The Routing Information Protocol (RIP) sends routing-update messages at regular intervals and when the network topology changes. When a device receives a RIP routing update that includes changes to an entry, the device updates its routing table to reflect the new route.

What is the purpose of RIP?

The Routing Information Protocol (RIP) is one of the oldest distance-vector routing protocols which employs the hop count as a routing metric. RIP prevents routing loops by implementing a limit on the number of hops allowed in a path from source to destination.

Is RIP still used?

RIP, like all routing protocols, is designed to disseminate network information pertinent to routers. At the most basic level, routers need to know what networks are reachable and how far away they are. RIP does this, and it’s still widely used today.

What is RIP in computer network?

Routing Information Protocol (RIP) is a distance-vector routing protocol. Routers running the distance-vector protocol send all or a portion of their routing tables in routing-update messages to their neighbors. You can use RIP to configure the hosts as part of a RIP network.

How do I set up RIP protocol?

To configure a basic RIP network:

  1. Configure the network interfaces. This example shows multiple loopback interface addresses to simulate attached networks. …
  2. Create the RIP group and add the interface. …
  3. Create the routing policy to advertise both direct and RIP-learned routes. …
  4. Apply the routing policy.

What does RIPv2 use to prevent routing loops?

Solution(By Examveda Team) RIPv2 uses the same timers and loop-avoidance schemes as RIPv1. Split horizon is used to stop an update from being sent out the same interface it was received on. Holddown timers allow time for a network to become stable in the case of a flapping link.

What port does RIP use?

port 520

RIP uses User Datagram Protocol (UDP) port 520. RIP has the following architectural limitations: The longest network path cannot exceed 15 hops (assuming that each network, or hop, has a cost of 1).

What routing protocols are RIP and RIPv2?

A, D. RIP and RIPv2 are distance vector routing protocols.

What is the multicast address of RIPv2?

224.0.0.9

RIPv2 Design
RIPv2 multicasts its routing table every 30 seconds to the multicast IP address 224.0. 0.9. RIPv2 is usually limited to accessing networks where it can interoperate with servers running routed or with non-Cisco routers.

What is the difference between RIP and static routing?

Dynamic routing is implemented in large networks. Static routing may not follow any specific protocol. Dynamic routing follows protocols like BGP, RIP and EIGRP. Static routing does not require any additional resources.

What do I need to tell my router in dynamic routing?

Dynamic routing is a technique in which a router learns about routing information without an administrator’s help and adds the best route to its routing table. A router running a dynamic routing protocol adds the best route to its routing table and can also determine another path if the primary route goes down.

Which is better static routing or dynamic routing?

Security

Static routing is more secure because it doesn’t share routes across the entire network. Dynamic routing creates more security risks because it shares complete routing tables across the network.

When would you choose to add static route S to a router?

Static routes are most often used to connect to a specific network or to provide a Gateway of Last Resort for a stub network. They can also be used to: Reduce the number of routes advertised by summarizing several contiguous networks as one static route. Create a backup route in case a primary route link fails.

What are the disadvantages of using static routing?

The disadvantages of static routing include:

  • They are not easy to implement in a large network.
  • Managing the static configurations can become time consuming.
  • If a link fails, a static route cannot reroute traffic.

How do I set a static IP address on my router?

How to Set a Static IP Address

  1. Access the Control Panel. In the Windows search bar, type in “ncpa. …
  2. Select the Network Adapter. …
  3. Select Properties. …
  4. Select Internet Protocol Version 4 (TCP/IPv4) …
  5. Manually enter IP address and subnet mask. …
  6. Save Settings. …
  7. Revert Back to DHCP. …
  8. Glossary.

What does IP route 0.0 0.0 0.0 0.0 mean?

In the Internet Protocol Version 4, the address 0.0. 0.0 is a non-routable meta-address used to designate an invalid, unknown or non-applicable target. This address is assigned specific meanings in a number of contexts, such as on clients or on servers.

How do I find my default route?

Find your router’s default gateway address

  1. Click. in the lower-left corner of the screen. Search for “cmd” and select Command Prompt.
  2. In the Command Prompt, type ipconfig Hit Enter.
  3. Your default gateway will appear next to Default Gateway.

What is the difference between IP default gateway and ip route?

ip default-gateway is used when the device doesn’t support L3 routing. ip route is used to configure static route for the devices support L3 routing.