How do I connect my infrared remote to my TV?

Turn on the TV and make sure that the set-top box is connected and on.

  1. On the TV remote, press the HOME button.
  2. Select Settings.
  3. The next steps will depend on your TV menu options: …
  4. Connect the IR Blaster. …
  5. Select OK.
  6. Place the IR Blaster near the remote sensor of the set-top box.


How do I pair my IR remote?

Turn on your TV or another device you wish to control. Press and hold the corresponding DEVICE and POWER buttons on the remote at the same time. Wait until the power button comes on, and then release both buttons. Pointing the remote at the TV or another device, press the Power button on the remote and wait 2 seconds.

How do I set up an infrared sensor?

The connections for the IR sensor with the Arduino are as follows: Connect the negative wire on the IR sensor to GND on the Arduino. Connect the middle of the IR sensor which is the VCC to 5V on the Arduino. Connect the signal pin on the IR sensor to pin 8 on the Arduino.

Why is my infrared remote not working?

Check the remote batteries. If removing and reinstalling the batteries don’t help, install new batteries and try again. Confirm the location of the IR sensor on your TV and point the remote directly towards the IR sensor. logo is printed on your TV, the sensor is beside it.

How do I know if my cable box is set to receive IR signals?

Check if the remote is sending an IR signal.



Point the remote at the camera, and then press and hold the Power button on the remote. As you hold the button down, look at the camera’s screen. If the remote is sending an IR signal, you will see a colored light coming from the remote control.

How do I find the frequency of my IR remote?

Quote from video: You have to make a potential divider circuit using the photodiode and a 330 ohm resistor which I've already attached. So we will connect this in reverse biased mode.

How do you program a remote to a TV?

Quote from the video:
Quote from video: One press and hold on the tv. Button. And you need the second finger to press and hold on on off power button so let's start this first press and hold. And press and hold the lights will disappear.

How do you check IR receiver is working or not?

You only need to connect a voltmeter to the IR diode and the remote control tester is finished. Set the multimeter so it measures DC voltage and turn it on. Hold the remote control close to the IR diode and push any button. If the remote control is working then the voltage shown on the display will quickly rise.

What is the IR code?

Ir-code definition



(InfraRed code) An infrared signal from a remote control that invokes some operation in A/V equipment such as power on/off, play, pause and stop.

How do I reset my infrared remote?

Quote from the video:
Quote from video: And work your way down the remote control. And you would go hold the power button down. One two three and let go then you go to the next button which on this one is the energy saver.

Why is my TV not responding to my remote?

Perform a power reset. If the issue is caused by an external factor, such as network service, data broadcasting, or connected devices, it may be improved by a power reset. For Android TV™ or Google TV™ models, unplug the power cord, wait two minutes, and then plug it in.

How do I fix an unresponsive remote?

Section B: Checking items of the remote control (common)

  1. Make sure none of the remote buttons are jammed.
  2. Reset the remote. …
  3. Clean the remote control terminals. …
  4. Replace with fresh batteries. …
  5. Perform a power reset on the TV. …
  6. For Android TV/Google TV: symptoms may improve by updating the software of the remote control.

How do you reset a remote?

For Android TVs released in 2015 or later, symptoms may improve by updating the software of the remote control.



Reset the remote control.

  1. Open the battery compartment cover and remove the batteries.
  2. Press and hold the Power button for three seconds.
  3. Insert the batteries again and close the battery compartment cover.