Measure and mark any copper pipe that the SharkBite fitting will be sliding on. Take a piece of copper pipe, slide it all the way into the safe seal depth and pipe deburring tool. The copper pipe must be marked once it bottoms out inside the measuring tool.

What is the depth of a 1/2 inch SharkBite fitting?

Pipe Insertion Depth Chart

SharkBite Fitting Size Nominal Pipe Size Pipe Insertion Depth (in.)
1/2 in. 1/2 in. CTS 0.95
5/8 in. 5/8 in. CTS 1.13
3/4 in. 3/4 in. CTS 1.10
1 in. 1 in. CTS 1.31

How big do SharkBite fittings get?

SharkBite fittings can be rotated even after assembly allowing for easier installation in tight places. With the largest range of fittings in the industry, SharkBite SKU selection carries sizes ranging form 1/4”-2”.

How much does a 3/4 inch SharkBite cost?

Compare Similar Brass Fittings

current product Best Seller
SharkBite SharkBite SharkBite
3/4 in. Push-to-Connect Brass Coupling Fitting 1/2 in. Push-to-Connect Brass Coupling Fitting 1 in. Push-to-Connect Brass Coupling Fitting
$927 $827 $1537
(2283) (2301) (2282)


How do you cut copper pipe for SharkBite?

Quote from the video:
Quote from video: Using your pex cutters mark the depth of cut with the tool. And then simply push in the pecs. You can see how flexible. And easy it is to use.

How do you stop a SharkBite from spinning?

Show activity on this post. Silicone tape along the base of the SharkBite valve should keep it from rotating on the pipe. Make sure the silicone tape overlaps itself (that’s how it sticks). Make sure you allow enough time for the tape to fuse to itself as well.

Do professional plumbers use SharkBite?

When and when not to use SharkBite fittings. Most professional plumbers believe that SharkBite fittings and other kinds of push-fit fittings should only be used as an emergency, temporary fix, and not for any enclosed or permanent plumbing system. However, there is a growing selection of DIYers who would disagree.

Do you sand copper for SharkBite?

Do not sand the copper pipe – while it’s the easiest way to smooth out the edge of the pipe, this practice should be avoided whenever possible since it disrupts the otherwise even pipe surface and may compromise the seal.

How do you measure copper pipe?

To find it, measure around the circumference of the pipe with flexible measuring tape. Divide the circumference by pi, or about 3.14159. For example, if the circumference is 12.57 inches (319 mm), you would divide by pi, and get an outside diameter of about 4 inches (100 mm).

Do you need the plastic insert for SharkBite fittings?

Do you need a tube liner with SharkBite large diameter fittings? Yes. A tube liner is required when using the SharkBite large diameter fittings in conjunction with PEX, PE-RT or HDPE pipe. Tube liners are not required when using SharkBite large diameter fittings with copper or CPVC.

Can you reuse SharkBites?

SharkBite fittings are reusable. Keep in mind that each time you use one on plastic pipe, the pipe may get scratched. If the scratches are deep enough, the pipe will bypass the seal inside of the fitting and create a leak. So yes, they’re reusable, but reuse them with caution.

How long do SharkBites last on copper?

Copper and PVC fittings can last 50 or more years. Even ProPress fittings have a warranty of 50 years (but who knows since they are so new).

Are SharkBite fittings as good as solder?

These groups of home owners feel SharkBite fittings are just as strong as soldering. A few of the criticisms of SharkBite and other push-fit fittings consist of; initially, push-fit fittings do not have the trustworthiness that soldering has. Soldering has actually been around much longer than push-fit fittings.

Are SharkBites a permanent fix?

Quick-connect and push-to-connect fittings are not permanent, but should only be reused for temporary installation. The lubricant on the collet of a SharkBite wears off after a while, and the O-ring of either fitting may stretch or wear out.

Do SharkBites ever fail?

Are Sharkbite fittings prone to failure? Yes. But all fittings are when installed improperly.

Can you use SharkBite fittings on hot water?

Yes, you can use SharkBite fittings on hot water lines. Remember, however, that they only work with copper, PEX, and CPVC pipes.

Can SharkBite be used on baseboard heat?

Are your standard Sharkbite fittings ok to use on radiant/hydronic copper baseboard heat? Good morning, Yes. All SharkBite Push-To-Connect fittings can withstand up to 200 PSI and 200 degrees Fahrenheit.

What is orange PEX pipe used for?

Designed for use on hot and cold potable water lines, Orange PEX tubing is commonly used for radiant floor and hydronic heating applications.

Whats better PEX or copper?

PEX pipe is not only cheaper than copper but more durable too. PEX is immune to corrosion and mineral build-up, and it’s not affected by electrolysis, which can cause small pinhole leaks in copper piping. Copper pipes can last anywhere from six months to the life of a building.

Can SharkBite fittings be used for gas?

You may damage the pipe if you use sharp instruments to open the SharkBite® PEX packaging. Don’t use natural gas, propane, fuel oil, or any other fluid, chemical or product with it. The SharkBite PEX tubing is not approved or intended for any other use.

Are shark bites code?

SharkBite Codes (Working)



SHARKBITE2 – Redeem for 200 Shark Teeth. 1BILLION – Redeem code for 100 Shark Teeth. SimonsSpace – Redeem code for 50 Shark Teeth. FROGGYBOAT – Redeem code for 50 Shark Teeth.

How do you remove a SharkBite fitter without tools?

Quote from the video:
Quote from video: Use an adjustable wrench. You know not a closed so the wrench.